Automatic cutting table operation instructions: First of all, we set parameters, open the man-machine interface, enter the home page, click width setting in the navigation bar below the home page, enter the width setting page, click the serial number 1 column, set the slitting data of the first knife, the first knife is basically cutting edge, slitting width is determined visually according to the material field situation, and manually adjust the position of the cutter. Therefore, the width of the first knife can be any width, the number is set to 1, the Angle is set to 0 degrees or positive Angle, according to the shape of the knife edge of the round knife is a single bevel or a double bevel to determine the feed Angle, and the feed speed is set on another page. Next, click the serial number 2 column, set the product slitting width, and then set the product slitting quantity, slitting quantity calculation method: Total width of the material to be cut ÷ slitting width = slitting number (take an integer). Please note that if the last cut wants to reverse trim, then the slitting number of column 2 should be reduced by one cut. Then click on column 3 of serial number and set the number to 1. Next set the feed speed, click back, enter the navigation bar feed setting page, feed speed has a variety of modes to choose from:

One is to manually set the single speed mode, see the video operation demonstration.

Second, the runner manually adjusts the speed mode, please see the video operation

demonstration.

Third, multi-speed automatic conversion mode, please see the video operation

demonstration.

After the feed speed is set, the operation of correcting the feed stroke is carried out on the

same page. Before the school knife, we first talk about how to replace and install the round

knife: First of all, we loosen the small screws on both sides of the cutter head, and then

unscrew the large nut on the outside of the cutter head, remove the cutter head, check

whether the cutter head plane is cracked or deformed, whether the small screw head is

normally lower than the cutter head plane, and then install the cutter head and round knife

after the check is correct, and lock the big nut. Then install the dial indicator to detect the

beating value of the round knife operation, adjust the pressure of the small screws on the

round knife according to the beating situation, and the normal standard is that the beating

of the round knife must be within 3 wires. Watch the video for a demonstration.

After the installation of the round knife, adjust the center point of the swing Angle of the

round knife. Take out the special calibration tool in the random tool, and install it on the

rotary pin of the swing Angle plate. Visually check whether the distance between the

vertical point of the round knife edge and the center line of the calibration tool iscoincident.

After the circular knife is installed and the center point of the swing Angle is corrected, the

feed stroke is corrected: First click on the calibration tool, wait for the round cutter seat to

automatically return to zero, long press the cross switch of manual feed tool is not loose,

visually observe the round knife edge slowly close to the cutting spindle, wait for the knife

edge to cut into the hose about 0.1-0.2mm, immediately release the manual feed switch,

such as the cutting depth is not ideal, you can also press the upper micro advance or micro

retreat for fine tuning, After the completion of the adjustment of the mechanical limit

screw under the water drag plate, the screw completely against the limit block and then

turn half a circle, and then lock the screw and cap, press the cross switch to confirm the

feed, the round knife automatically return to the circle point, the adjustment of the feed

stroke of the round knife is completed, short press the manual feed, the round knife seat

automatically enters the starting position to be cut. There are two control methods for the

starting position of the round tool holder to be cut, one is photoelectric induction

positioning, and the other is CNC intelligent positioning. Different models have different

control methods, please choose freely according to your operating preferences.

Next, press the motor to start the cross switch, adjust the rotary knife speed and the

spindle speed according to the material scuttling requirements, and then load the material,

manually move the cutter horizontally to the first cutter scuttling position, press the

automatic start to enter the automatic scuttling process, after the complete supporting

material, the cutting table automatically returns to the first cutter position, so reciprocating

to complete the entire scuttling operation.

，